1. Conformity assessment happens before shipment
The single most important rule: where a pre-shipment conformity scheme applies, the assessment must be completed before the goods ship. In most cases it cannot be obtained after arrival at the port, and a container held at the port accrues charges quickly.
Nigeria — SONCAP. The Standards Organisation of Nigeria operates a conformity assessment programme for regulated imports. In broad terms the chain is product testing against applicable standards, a Product Certificate (PC), and a per-shipment certificate used for customs clearance; the importer completes local steps such as Form M. Faucets, showers and sanitary ware are commonly treated as regulated categories. Confirm the current regulated product list and the correct route with your appointed inspection agency — the details, and who is responsible for each step, matter more than the acronym.
Kenya — PVoC / KEBS. Pre-Export Verification of Conformity leads to a Certificate of Conformity (CoC) issued before shipment. A typical application requires an import declaration form (IDF), a packing list and a commercial invoice showing FOB value, plus product quality evidence — usually a test report from an ISO/IEC 17025-accredited laboratory, or a manufacturer's test report together with ISO 9001 certification. Reports are generally expected against KS/KEBS, international or recognised standards rather than a supplier's domestic standard. Inspection fees are commonly calculated as a percentage of FOB value with minimum and maximum caps; verify the current schedule and any additional requirements with your inspection agency. Product and outer packaging must carry the country-of-origin marking and the manufacturer name or trademark.
South Africa. Verify whether SABS or other approvals apply to your specific products and finishes before ordering.
Other markets. Several African countries run their own PVoC/CoC schemes, and certificate-of-origin requirements have been added or tightened in some destinations in recent years. Do not assume one certificate covers a region. Confirm the destination-specific list with your broker — not with your supplier alone.
A practical habit: put "conformity scheme and appointed inspection agency" as a line item in the purchase order, with responsibility for each step assigned in writing.
2. The document pack to require before you pay the balance
Document | Who provides | What to check |
ISO 9001 certificate | Manufacturer | Valid, in the manufacturer's legal name |
Product test report | Accredited lab (ISO/IEC 17025) | Standard accepted in destination, product and finish covered |
Technical specification sheet | Supplier | Material, dimensions, flow rate, pressure range, finish, components |
Product photos | Supplier | Clear views of product and markings |
Packing list & commercial invoice | Supplier | FOB value in USD, consistent HS description |
Certificate of Origin (COO) | Exporter / chamber | Required by destination, issued for the correct shipment |
IPPC / fumigation evidence | Packer | For any wooden packaging or crate |
Product Certificate / CoC support | Supplier + agency | Applied for before vessel cut-off |
Origin & manufacturer markings | Factory | On both product and outer carton |
Spare parts list & installation manual | Supplier | Part numbers, reorder terms, local-language manual if needed |
Ask your account manager which of these we can supply for your destination, and have the pack reviewed by your inspection agency before production is finished — not after.
3. From FOB to landed: the lines buyers forget
Landed cost per sellable unit = (FOB value + ocean freight + insurance + inspection and certification fees + import duty and taxes + port and clearance charges + inland transport + packaging and reinforcement + breakage and spare-parts allowance + payment, FX and financing costs) ÷ sellable units
- Incoterm decides who pays what. FOB, CIF, EXW and DDP are not interchangeable. State the chosen term explicitly in the contract and make sure the quotation is built on it.
- Ocean freight: FCL vs LCL. Sanitary ware and shower sets are bulky and, where ceramics or glass are involved, fragile. Full containers reduce handling and damage risk; LCL gives flexibility for trial orders. Transit times vary by carrier, port and season — get a current quote rather than planning from a published number.
- Duty and taxes vary widely by HS code and destination. Classify each product correctly and have a licensed broker confirm the applicable rate. Never build a margin on an assumed tariff.
- Inspection, testing and certification add real cost, and re-testing or re-inspection after a failed submission adds more.
- Packaging is not overhead. Multi-layer protection, five- or seven-ply cartons, EPE/foam corner protection, and crating for heavy items are what keep the "sellable units" figure close to the "shipped units" figure. Wooden packaging needs IPPC treatment and marking.
- Breakage and spares. Budget a spare-parts allowance — cartridges, seals, hoses, spray heads — from the first order. It is also the basis of an after-sales promise you can actually keep.
- Payment terms, FX and lead time. T/T, L/C and other terms carry different costs and risks; currency movement over a production cycle can erase a thin margin.
4. A workable sequence (order matters more than the number of days)
- Confirm HS codes, destination requirements and the appointed inspection agency
2. Agree the specification and the full documentation pack with the supplier
3.Complete product testing and any Product Certificate application
4.Production, internal QC, and packing photos for your records
5.Pre-shipment inspection and CoC application — before vessel cut-off
6.Booking, shipping documents, Certificate of Origin
7.Customs clearance, duty and tax payment, inland delivery
8.Receiving inspection: log breakage, register spare parts, feed results back into the next order
Build the inspection step into your production schedule, not into your shipping schedule. A certificate that should have been issued before loading is the most common avoidable delay in this trade.
6. What to do next
Tell us your destination port, product mix and chosen Incoterm. We will prepare the specification and documentation pack for your inspection agency to review, and quote on the basis you actually need — so the number you approve is close to the number that lands.
Next step: request a documentation pack and a landed-cost quotation for your destination. [Link: /contact] [Link: /products]
Related reading: [Post 1 title — specifying fittings for hard water and low pressure] and [Post 3 title — building a private-label shower range].
Frequently asked questions
Can a SONCAP or CoC certificate be obtained after the goods arrive? Generally no. These are pre-shipment schemes; plan the assessment into production and assume the port cannot fix a missing certificate.
Who handles Form M or the IDF? The importer, locally, through the relevant authority or bank. Clarify this with your broker and write the responsibility into the order.
Does one certificate cover repeat shipments? It depends on the scheme and whether a registered or product-certificate route is available for frequent exporters. Ask your inspection agency which route fits your order frequency.
Do I need a separate test report for each finish? Finishes can affect the declared material and composition. Ask your agency which variants the report must cover before testing.